RESEARCH PAPERS: Forced Convection

Numerical Simulation of Flow Field and Heat Transfer of Streamlined Cylinders in Cross Flow

[+] Author and Article Information
Zhihua Li, Susan C. Mantell

Department of Mechanical Engineering, University of Minnesota, 111 Church St., SE, Minneapolis, MN 55455

Jane H. Davidson

Department of Mechanical Engineering, University of Minnesota, 111 Church St., SE, Minneapolis, MN 55455jhd@me.umn.edu

J. Heat Transfer 128(6), 564-570 (Dec 23, 2005) (7 pages) doi:10.1115/1.2188463 History: Received March 08, 2005; Revised December 23, 2005

The drag and convective heat transfer coefficients along the outer surface of lenticular and elliptical tubes with minor-to-major axis ratios of 0.3, 0.5, and 0.8 were determined numerically for cross-flow Reynolds numbers from 500 to 104. The two-dimensional, unsteady Navier-Stokes equations and energy equation were solved using the finite volume method. Laminar flow was assumed from the front stagnation point up to the point of separation. Turbulent flow in the wake was resolved using the shear stress transport k-ω model. Local heat transfer, pressure and friction coefficients as well as the total drag coefficient and average Nusselt number are presented. The results for streamlined tubes are compared to published data for circular and elliptical cylinders. Drag of the elliptical and lenticular cylinders is similar and lower than a circular cylinder. Drag can be reduced by making the streamlined cylinders more slender. Drag is relatively insensitive to Reynolds number over the range studied. An elliptical cylinder with an axis ratio equal to 0.5 reduces pressure drop by 30–40% compared to that of a circular cylinder. The Nusselt numbers of lenticular and elliptical cylinders are comparable. The average Nusselt number of an elliptical or lenticular cylinder with axis ratio of 0.5 and 0.3 is 15–35% lower than that of a circular cylinder.

Copyright © 2006 by American Society of Mechanical Engineers
Your Session has timed out. Please sign back in to continue.



Grahic Jump Location
Figure 1

Example of a “shaped” polymer tube. The outer surface of the tube is an ellipse. The inner flow passage is circular. The non-uniform wall is selected to minimize the conductive resistance across the wall and to prevent deformation and strain failure (5).

Grahic Jump Location
Figure 2

Streamlined outer profile of (a) elliptical, and (b) lenticular tubes. The outer surface of a lenticular cylinder is formed by two symmetrically intersected arcs, each given by (rcosα)2+(rsinα+Rl−ro)2=Rl2, where and λo is the length ratio of the minor to major axis of the outer surface. A value of λo=1 represents a circular cylinder. The cylinders become more slender as λo is decreased.

Grahic Jump Location
Figure 3

Computational domain and boundary conditions of flow and heat transfer

Grahic Jump Location
Figure 4

Triangular and quad meshes for flow over an individual elliptical cylinder

Grahic Jump Location
Figure 5

Comparison of predicted local friction coefficient with experiment (8) for an elliptical cylinder with λo=0.5 at ReD=3200

Grahic Jump Location
Figure 6

Comparison of numerical drag coefficient with experiment (7-8) for an elliptical cylinder with λo=0.5

Grahic Jump Location
Figure 7

Comparison of predicted local Nusselt number with experiment (12) and an empirical correlation (8) for an elliptical cylinder with λo=0.5 at ReD=3074

Grahic Jump Location
Figure 8

Comparison of predicted average Nusselt number with empirical correlations (8,12-13) for an elliptical cylinder with λo=0.5

Grahic Jump Location
Figure 9

Friction, pressure and drag coefficient of an elliptical cylinder with λo=0.3

Grahic Jump Location
Figure 10

Comparison of drag coefficients of elliptical, lenticular and circular cylinders. The drag coefficient of a circular cylinder is calculated from correlation of (22).

Grahic Jump Location
Figure 11

Average Nusselt number of streamlined cylinders with λo=0.3, 0.5, and 0.8 at 500⩽ReD⩽104, (a) elliptical, (b) lenticular. The Nusselt number of the circular cylinder is calculated from correlations provided by (8).



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In