Research Papers: Evaporation, Boiling, and Condensation

Evaporating Liquid Film Flow in the Presence of Micro-Encapsulated Phase Change Materials: A Numerical Study

[+] Author and Article Information
Yasmin Khakpour

Multi-Scale Heat Transfer Laboratory,
Department of Mechanical Engineering,
Worcester Polytechnic Institute,
Worcester, MA 01609
e-mail: ykhakpour@alum.wpi.edu

Jamal Seyed-Yagoobi

Multi-Scale Heat Transfer Laboratory,
Department of Mechanical Engineering,
Worcester Polytechnic Institute,
Worcester, MA 01609
e-mail: jyagoobi@wpi.edu

Contributed by the Heat Transfer Division of ASME for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received February 18, 2014; final manuscript received August 15, 2014; published online November 18, 2014. Assoc. Editor: Giulio Lorenzini.

J. Heat Transfer 137(2), 021501 (Feb 01, 2015) (9 pages) Paper No: HT-14-1081; doi: 10.1115/1.4028808 History: Received February 18, 2014; Revised August 15, 2014; Online November 18, 2014

This paper numerically investigates the heat transfer characteristics of a mesoscale liquid film slurry flow containing micro-encapsulated phase change material (MEPCM) in the presence of evaporation. The two-phase evaporating liquid film flow is modeled using one-fluid volume-of-fluid (VOF) formulation. During the evaporation process of the base fluid, the concentration of MEPCM in the slurry film increases as it flows along a heated plate, resulting in a continuous variation of its effective thermal properties. The effect of MEPCM on the evolution of the liquid film thickness under different operating conditions is presented. It is shown that the MEPCM suppresses the rate of decline in the liquid film thickness, which results in a higher heat transfer coefficient compared to that of pure liquid film under similar operating conditions. This study also provides an understanding towards delaying of the dry-out condition in slurry liquid film flow evaporation compared to that of the pure fluid.

Copyright © 2015 by ASME
Your Session has timed out. Please sign back in to continue.


Kasza, K., and Chen, M., 1985, “Improvement of the Performance of Solar Energy or Waste Heat Utilization Systems by Using Phase-Change Slurry as an Enhanced Heat-Transfer Storage Fluid,” ASME J. Sol. Energy Eng., 107(3), pp. 229–236. [CrossRef]
Colvin, D. P., and Mulligan, J. C., 1986, “Spacecraft Heat Rejection Methods: Active and Passive Heat Transfer for Electronic Systems-Phase I,” US Air Force Wright Aeronautical Labs, Daytona, OH, Technical Report No. AFWAL-TR-3074.
Colvin, D. P., and Mulligan, J. C., 1987, “Microencapsulated Phase Change for Storage of Heat,” NASA George C. Marshall Space Flight Center, Huntsville, AL, Technical Report No. MFSA-27198.
Goel, M., Roy, S., and Sengupta, S., 1994, “Laminar Forced Convection Heat Transfer in Microcapsulated Phase Change Material Suspensions,” Int. J. Heat Mass Transfer, 37(4), pp. 593–604. [CrossRef]
Inaba, H., Kim, M., and Horibe, A., 2004, “Melting Heat Transfer Characteristics of Microencapsulated Phase Change Material Slurries With Plural Microcapsules Having Different Diameters,” ASME J. Heat Transfer, 126(4), pp. 558–565. [CrossRef]
Alvarado, J. L., Marsh, C., Sohn, C., Phetteplace, G., and Newell, T., 2007, “Thermal Performance of Microencapsulated Phase Change Material Slurry in Turbulent Flow Under Constant Heat Flux,” Int. J. Heat Mass Transfer, 50(9–10), pp. 1938–1952. [CrossRef]
Wang, X., Niu, J., Li, Y., Zhang, Y., Wang, X., Chen, B., Zeng, R., and Song, Q., 2008, “Heat Transfer of Microencapsulated PCM Slurry Flow in a Circular Tube,” AIChE J., 54(4), pp. 1110–1120. [CrossRef]
Hao, Y. L., and Tao, Y. X., 2004, “A Numerical Model for Phase-Change Suspension Flow in Microchannels,” Numer. Heat Transfer, Part A, 46(1), pp. 55–77. [CrossRef]
Xing, K. Q., Tao, Y. X., and Hao, Y. L., 2004, “Performance Evaluation of Liquid Flow With NPCM in Microchannels,” ASME 2004 Heat Transfer/Fluids Engineering Summer Conference, Charlotte, NC, July 11–15, pp. 283–292.
Kuravi, S., Kota, K. M., Du, J., and Chow, L. C., 2009, “Numerical Investigation of Flow and Heat Transfer Performance of Nano-Encapsulated Phase Change Material Slurry in Microchannels,” ASME J. Heat Transfer, 131(6), p. 062901. [CrossRef]
Sabbah, R., Farid, M. M., and Al-Hallaj, S., 2009, “Micro-Channel Heat Sink With Slurry of Water With Micro-Encapsulated Phase Change Material: 3D-Numerical Study,” Appl. Therm. Eng., 29(2–3), pp. 445–454. [CrossRef]
Sabbah, R., Seyed-Yagoobi, J., and Al-Hallaj, S., 2011, “Heat Transfer Characteristics of Liquid Flow With Micro-Encapsulated Phase Change Material: Numerical Study,” ASME J. Heat Transfer, 133(12), p. 121702. [CrossRef]
Sabbah, R., Seyed-Yagoobi, J., and Al-Hallaj, S., 2012, “Heat Transfer Characteristics of Liquid Flow With Micro-Encapsulated Phase Change Materials: Experimental Study,” ASME J. Heat Transfer, 134(4), p. 044501. [CrossRef]
Thome, J., Groll, M., and Mertz, R., 2003, “Heat Transfer and Fluid Flow in Microchannels,” Heat Transfer and Fluid Flows in Microchannels, Heat Exchanger Design Update, Vol. 2, Begell House, New York.
Kandlikar, S., 2001, “Two-Phase Flow Patterns, Pressure Drop and Heat Transfer During Boiling in Minichannel and Microchannel Flow Passages of Compact Heat Exchangers,” Compact Heat Exchangers and Enhancement Technology for the Process Industries, Begell House, New York, pp. 319–334.
Bergles, A. E., Lienhard, V, J. H., Kendall, G. E., and Griffith, P., 2003, “Boiling and Evaporation in Small Diameter Channels,” Heat Transfer Eng., 24(1), pp. 18–40. [CrossRef]
Thome, J., Dupont, V., and Jacobi, A., 2004, “Heat Transfer Model for Evaporation in Microchannels. Part I: Presentation of the Model,” Int. J. Heat Mass Transfer, 47(14–16), pp. 3375–3385. [CrossRef]
Mehendale, S., and Jacobi, A., 2000, “Evaporative Heat Transfer in Mesoscale Heat Exchangers,” ASHRAE Trans., 106(1), pp. 446–452.
Jacobi, A. M., and Thome, J. R., 2002, “Heat Transfer Model for Evaporation of Elongated Bubble Flows in Microchannels,” ASME J. Heat Transfer, 124(6), pp. 1131–1136. [CrossRef]
Lakehal, D., Meier, M., and Fulgosi, M., 2002, “Interface Tracking Towards the Direct Simulation of Heat and Mass Transfer in Multiphase Flows,” Int. J. Heat Fluid Flow, 23(3), pp. 242–257. [CrossRef]
Xiong, Q., Deng, L., Wang, W., and Ge, W., 2011, “SPH Method for Two-Fluid Modeling of Particle–Fluid Fluidization,” Chem. Eng. Sci., 66(9), pp. 1859–1865. [CrossRef]
Xiong, Q., Li, B., and Xu, J., 2013, “GPU-Accelerated Adaptive Particle Splitting and Merging in SPH,” Comput. Phys. Commun., 184(7), pp. 1701–1707. [CrossRef]
Xiong, Q., Li, B., Xu, J., Wang, X., Wang, L., and Ge, W., 2012, “Efficient 3D DNS of Gas–Solid Flows on Fermi GPGPU,” Comput. Fluids, 70, pp. 86–94. [CrossRef]
Zhao, J. J., Duan, Y. Y., Wang, X. D., and Wang, B. X., 2011, “Effect of Nanofluids on Thin Film Evaporation in Microchannels,” J. Nanopart. Res., 13(10), pp. 5033–5047. [CrossRef]
Charunyakorn, P., Sengupta, S., and Roy, S., 1991, “Forced Convection Heat Transfer in Microencapsulated Phase Change Material Slurries: Flow in Circular Ducts,” Int. J. Heat Mass Transfer, 34(3), pp. 819–833. [CrossRef]
Sabbah, R., 2008, “Numerical and Experimental Investigation of Heat Transfer Characteristics of Liquid Flow With Micro-Encapsulated Phase Change Material,” Ph.D. thesis, Illinois Institute of Technology, Chicago, IL.
Sinha-Ray, S., Sahu, R. P., and Yarin, A. L., 2011, “Nano-Encapsulated Smart Tunable Phase Change Materials,” Soft Matter, 7(19), pp. 8823–8827. [CrossRef]
Sanchez-Silva, L., Rodríguez, J. F., Romero, A., Borreguero, A. M., Carmona, M., and Sánchez, P., 2010, “Microencapsulation of PCMs With a Styrene-Methyl Methacrylate Copolymer Shell by Suspension-Like Polymerisation,” Chem. Eng. J., 157(1), pp. 216–222. [CrossRef]
Dupont, ISCEON 39TC(R-423A): Technical Information.
Sánchez Silva, L., Rodríguez, J. F., Carmona, M., Romero, A., and Sánchez, P., 2011, “Thermal and Morphological Stability of Polystyrene Microcapsules Containing Phase-Change Materials,” J. Appl. Polym. Sci., 120(1), pp. 291–297. [CrossRef]
Guyer, E. C., and Brownell, D. L., 1999, Handbook of Applied Thermal Design, CRC Press, Boca Raton, FL.
Maxwell, J. C., 1881, A Treatise on Electricity and Magnetism, 3rd ed., Dover, Mineola, NY.
Vand, V., 1945, “Theory of Viscosity of Concentrated Suspensions,” Nature (London), 155, pp. 364–365. [CrossRef]
Leal, L. G., 1973, “On the Effective Conductivity of a Dilute Suspension of Spherical Drops in the Limit of Low Particle Peclet Number,” Chem. Eng. Commun., 1(1), pp. 21–31. [CrossRef]
Nir, A., and Acrivos, A., 1976, “The Effective Thermal Conductivity of Sheared Suspensions,” J. Fluid Mech., 78(1), pp. 33–48. [CrossRef]
ANSYS INC., 2008, “FLUENT V12.0 User's Guide,” Lebanon, NH.
Carey, V., 1992, Vapor–Liquid Phase Change Phenomena: An Introduction to the Thermophysics of Vaporization and Condensation Processes in Heat Transfer Equipment, Hemisphere Publishing, New York.
Faghri, A., and Zhang, Y., 2006, Transport Phenomena in Multiphase Systems, Academic Press, New York.


Grahic Jump Location
Fig. 1

Schematic of 2-D representation of the numerical domain (not to scale)

Grahic Jump Location
Fig. 2

Variation of the specific heat of PCM with temperature [27]

Grahic Jump Location
Fig. 3

Variation of slurry's specific heat with temperature for the case of pure R134a, 5% and 15% MEPCM slurry

Grahic Jump Location
Fig. 4

Comparison of current numerical model and Nusselt theory for falling film evaporation [38] for the evolution of liquid film thickness and local average heat transfer coefficient

Grahic Jump Location
Fig. 5

Temperature distribution and interface profile for q"w=400W/m2 and Gin = 10 kg/m2 · s for (a) pure R134a and (b) ξin = 15% MEPCM slurry

Grahic Jump Location
Fig. 6

Variation of the Peclet number along the channel for q"w=400 W/m2

Grahic Jump Location
Fig. 7

Variation of liquid film thickness along the channel for q"w=400 W/m2: (a) effect of MEPCM inlet concentration, ξ and (b) effect of liquid inlet mass flux, G

Grahic Jump Location
Fig. 8

Variation of evaporation heat transfer coefficient along the channel for q"w=400 W/m2: (a) effect of MEPCM inlet concentration, ξ and (b) effect of liquid inlet mass flux, G

Grahic Jump Location
Fig. 9

Variation of average heat transfer coefficient with liquid film inlet temperature for pure R134a and MEPCM slurry at ξ = 15%

Grahic Jump Location
Fig. 10

Variation of MEPCM concentration along the channel for various applied heat fluxes



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In