Bistable microsystems have drawn considerable interest from the MEMS/NEMS research community not only due to their broad applicability in commercial applications, such as switching, but also because of the rich dynamic behavior they commonly exhibit. While a number of prior investigations have studied the dynamics of bistable microsystems, comparatively few works have sought to characterize their transient behavior. The present effort seeks to address this through the modeling and analysis of an optically-actuated, bistable MEMS switch. This work begins with the development of a distributed-parameter representation for the system, which is subsequently reduced to a lumped-mass analog and analyzed through the use of numerical simulation. The influence of various system and excitation parameters, including the applied axial load and optical actuation profile, on the system’s transient response is then investigated. Ultimately, the methodologies and results presented herein should provide for a refined predictive design capability for optically-actuated, bistable MEMS devices.
Skip Nav Destination
e-mail: kumar2@purdue.edu
e-mail: jfrhoads@purdue.edu
Article navigation
April 2012
Research Papers
Modeling and Analysis of an Optically-Actuated, Bistable MEMS Device
Vijay Kumar,
Vijay Kumar
School of Mechanical Engineering, Birck Nanotechnology Center, and Ray W. Herrick Laboratories,
e-mail: kumar2@purdue.edu
Purdue University
, West Lafayette
, IN 47907
Search for other works by this author on:
Jeffrey F. Rhoads
Jeffrey F. Rhoads
School of Mechanical Engineering, Birck Nanotechnology Center, and Ray W. Herrick Laboratories,
e-mail: jfrhoads@purdue.edu
Purdue University
, West Lafayette
, IN 47907
Search for other works by this author on:
Vijay Kumar
School of Mechanical Engineering, Birck Nanotechnology Center, and Ray W. Herrick Laboratories,
Purdue University
, West Lafayette
, IN 47907e-mail: kumar2@purdue.edu
Jeffrey F. Rhoads
School of Mechanical Engineering, Birck Nanotechnology Center, and Ray W. Herrick Laboratories,
Purdue University
, West Lafayette
, IN 47907e-mail: jfrhoads@purdue.edu
J. Comput. Nonlinear Dynam. Apr 2012, 7(2): 021007 (7 pages)
Published Online: January 6, 2012
Article history
Received:
January 11, 2011
Revised:
September 8, 2011
Accepted:
September 9, 2011
Online:
January 6, 2012
Published:
January 6, 2012
Citation
Kumar, V., and Rhoads, J. F. (January 6, 2012). "Modeling and Analysis of an Optically-Actuated, Bistable MEMS Device." ASME. J. Comput. Nonlinear Dynam. April 2012; 7(2): 021007. https://doi.org/10.1115/1.4005080
Download citation file:
Get Email Alerts
Cited By
Investigation of Nonlinear Dynamic Behaviors of Vertical Rotor System Supported by Aerostatic Bearings
J. Comput. Nonlinear Dynam (January 2025)
Electric Circuit Analogs of First-Order Dual-Phase-Lag Diffusion
J. Comput. Nonlinear Dynam
Related Articles
Bistable Buckled Beam: Modeling of Actuating Force and Experimental Validations
J. Mech. Des (October,2009)
Static and Dynamic Analysis of Carbon Nanotube-Based Switches
J. Eng. Mater. Technol (July,2004)
Modeling of Initially Curved Beam Structures for Design of Multistable MEMS
J. Appl. Mech (January,2012)
An Efficient Reduced-Order Model to Investigate the Behavior of an Imperfect Microbeam Under Axial Load and Electric Excitation
J. Comput. Nonlinear Dynam (January,2013)
Related Proceedings Papers
Related Chapters
Smart Semi-Active Control of Floor-Isolated Structures
Intelligent Engineering Systems Through Artificial Neural Networks, Volume 17
Concluding Remarks and Future Work
Ultrasonic Welding of Lithium-Ion Batteries
Monitoring and Assessment of Campus Network Performance
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)