The expanding use of prestressed concrete in offshore structures, both fixed and floating, in ever more hostile environments has generated intense interest in its fatigue endurance capabilities, even though, as far as it is known, no fatigue problems have arisen in actual structures. Although concrete does suffer progressive loss of strength with increasing number of cycles, a comparison of the Wo¨hler curves developed on the basis of laboratory tests with the probable distribution of compressive stresses during a service life in an environment such as the North Sea shows extremely low cumulative usage at the high-cycle end of the spectrum. However, significant damage can occur at the low-cycle, high-amplitude end of the spectrum under a relative small number of cycles of very high magnitude. This damage is displayed by a reduction in stiffness and by rapidly increasing axial and lateral strains that lead to cracking and spalling. Repeated cycling into high compressive ranges causes a substantial increase in creep, reducing the effective prestress. Confining reinforcement resists lateral deformation and delays compressive fatigue failure. Cycling into the tensile range a large number of times can produce cracking due to tensile fatigue at about half the static tensile strength. Cracking also can occur due to overload, accident, construction procedures, and thermal strains. Repeated excursions of submerged concrete into the crack opening range leads to pumping of water in and out of the crack and hydraulic wedging, leading to splitting of the concrete. Cracking subjects the reinforcing and prestressing steel to cyclic tension. Loss of bond ensues and may lead to eventual fatigue failure. Adequate endurance can be ensured by prestressing, so as to avoid a large number of cycles extending into the crack opening range, and by the provision of adequate percentages of steel across the section plus transverse and confining steel. Cyclic membrane shear may produce diagonal tension cracking at about half the static strength. Conventional reinforcing in an orthogonal grid pattern is very inefficient in resisting such cracking. Crack widths grow rapidly. Repeated loading may lead to abrasion of concrete surfaces and failure of the steel due to combined axial force and bending. Vertical prestress is an efficient and practical method of resisting high-amplitude cyclic shear. For the typical concrete sea structure, high-cycle, low-amplitude, cumulative fatigue is not a significant problem. However low-cycle, high-amplitude fatigue requires consideration, expecially when there are numerous cycles into the tensile cracking range. In this latter case, fatigue of the steel and/or concrete may occur unless adequate amounts of steel are provided to ensure that crack widths and steel stresses are kept within allowable values.
Skip Nav Destination
Article navigation
March 1980
Research Papers
High and Low-Cycle Fatigue Behavior of Prestressed Concrete in Offshore Structures
B. C. Gerwick,
B. C. Gerwick
University of California, Berkeley, Calif. 94720
Search for other works by this author on:
W. J. Venuti
W. J. Venuti
San Jose State University, San Jose, Calif. 95192
Search for other works by this author on:
B. C. Gerwick
University of California, Berkeley, Calif. 94720
W. J. Venuti
San Jose State University, San Jose, Calif. 95192
J. Energy Resour. Technol. Mar 1980, 102(1): 18-23 (6 pages)
Published Online: March 1, 1980
Article history
Received:
October 10, 1979
Online:
October 22, 2009
Citation
Gerwick, B. C., and Venuti, W. J. (March 1, 1980). "High and Low-Cycle Fatigue Behavior of Prestressed Concrete in Offshore Structures." ASME. J. Energy Resour. Technol. March 1980; 102(1): 18–23. https://doi.org/10.1115/1.3227842
Download citation file:
Get Email Alerts
Cited By
Related Articles
Cycle-Dependent and Time-Dependent Bone Fracture With Repeated Loading
J Biomech Eng (May,1983)
Elastic and Viscoelastic Properties of the Human Pubic Symphysis Joint: Effects of Lateral Impact Loading
J Biomech Eng (June,2001)
Underwater Wet Repair Welding and Strength Testing on Pipe-Patch Joints
J. Offshore Mech. Arct. Eng (November,1998)
Shear Strength of a Thermal Barrier Coating Parallel to the Bond Coat
J. Eng. Mater. Technol (January,1998)
Related Proceedings Papers
Related Chapters
Understanding the Problem
Design and Application of the Worm Gear
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Compromise between Tensile and Fatigue Strength
New Advanced High Strength Steels: Optimizing Properties