This investigation concerns the strongly scattering mechanical properties of a 17 MoV 84 creep resistant steel. Emphasis is laid on the effect on microstructure of heat-treatment. The mechanical tests made after various austenitizing treatments, cooling rates, and tempering temperatures revealed that a complex relationship existed between the mechanical properties and microstructure in the steel precipitation hardened by vanadium carbides. In spite of constant tensile strength, the impact and creep properties in the steel therefore differ widely, due to relatively small microstructural effects. The study shows that the microstructural constituents, i.e., martensite, lower bainite, upper bainite in aciculare and globulare forms, as well as pre-eutectoid ferrite, all influence the room temperature ductility in a similar way to the creep ductility. However, in the case of creep strength, similar microstructural constituents have almost the reverse effect. As a result of these contrasting effects, it is not possible to obtain good ductility and creep properties at the same time. Any heat-treatments recommended can therefore only be a compromise between the properties desired.
Skip Nav Destination
Article navigation
April 1967
This article was originally published in
Journal of Engineering for Power
Research Papers
Influence of Microstructure and Heat-Treatment on Impact and Creep Properties of a Low Alloy CrMoV Turbine Steel
K. Relander,
K. Relander
Rautaruukki O. Y., Helsinki, Finland
Search for other works by this author on:
T. Geiger
T. Geiger
Sulzer Brothers, Winterthur, Switzerland
Search for other works by this author on:
K. Relander
Rautaruukki O. Y., Helsinki, Finland
T. Geiger
Sulzer Brothers, Winterthur, Switzerland
J. Eng. Power. Apr 1967, 89(2): 238-246 (9 pages)
Published Online: April 1, 1967
Article history
Received:
December 17, 1965
Online:
August 25, 2011
Article
Article discussed|
View article
Connected Content
Citation
Relander, K., and Geiger, T. (April 1, 1967). "Influence of Microstructure and Heat-Treatment on Impact and Creep Properties of a Low Alloy CrMoV Turbine Steel." ASME. J. Eng. Power. April 1967; 89(2): 238–246. https://doi.org/10.1115/1.3616660
Download citation file:
18
Views
Get Email Alerts
Cited By
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Effect of Different Heat Treatments on Mechanical Properties of Laser Sintered Additive Manufactured Parts
J. Manuf. Sci. Eng (November,2017)
Heat Treatment Selection and Forming Strategies for 6082 Aluminum Alloy
J. Eng. Mater. Technol (October,2009)
Continuous Drive Friction Welding of AISI 8630 Low-Alloy Steel: Experimental Investigations on Microstructure Evolution and Mechanical Properties
J. Manuf. Sci. Eng (July,2022)
Tensile Property Improvements of Spinodal Cu-15Ni-8Sn by Two-Phase Heat Treatment
J. Eng. Mater. Technol (July,1982)
Related Proceedings Papers
Related Chapters
Model and Simulation of Low Elevation Ground-to-Air Fading Channel
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)
Scattering of Out-Plane Line Source Load by a Shallow-Embedded Circular Lining Structure and the Ground Motion
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)
The MCRT Method for Participating Media
The Monte Carlo Ray-Trace Method in Radiation Heat Transfer and Applied Optics