This paper documents the process of determining the internal geometric configuration of a component by optimizing the global performance of the installation that uses the component. The example chosen is the crossflow heat exchanger used in the environmental control system of a modern aircraft. The optimization of global performance is achieved by minimizing the total entropy generation rate of the installation. There are three degrees of freedom in the heat exchanger configuration (the length-to-width and height-to-width aspect ratios, and the separator plate spacing ratio), which is subjected to two global constraints: total component volume, and total wall material volume (or weight/density) of wall material. Numerical results show how the optimal configuration responds to changes in specified external parameters such as volume, weight, Mach number, diffuser inlet cross-sectional area, and the pressure at which the cabin air is initially bled from the engine compressor. It is shown that the optimal configuration is robust and that major features such as the ratios of channel spacings and flow lengths are relatively insensitive to changes in some of the external parameters. It is also shown that the optimal heat exchanger geometry is insensitive to the thermodynamic irreversibility caused by discharging the used ram air into the ambient.
Skip Nav Destination
Article navigation
Technical Papers
Integrative Thermodynamic Optimization of the Crossflow Heat Exchanger for an Aircraft Environmental Control System
Jose V. C. Vargas,
Jose V. C. Vargas
Department of Mechanical Engineering and Materials Science, Duke University, Box 90300, Durham, NC 27708-0300
Search for other works by this author on:
Adrian Bejan,
Adrian Bejan
Department of Mechanical Engineering and Materials Science, Duke University, Box 90300, Durham, NC 27708-0300
Search for other works by this author on:
David L. Siems
David L. Siems
The Boeing Company, MC S106-7075, PO Box 516, Saint Louis, MO 63166-0519
Search for other works by this author on:
Jose V. C. Vargas
Department of Mechanical Engineering and Materials Science, Duke University, Box 90300, Durham, NC 27708-0300
Adrian Bejan
Department of Mechanical Engineering and Materials Science, Duke University, Box 90300, Durham, NC 27708-0300
David L. Siems
The Boeing Company, MC S106-7075, PO Box 516, Saint Louis, MO 63166-0519
Contributed by the Heat Transfer Division for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received by the Heat Transfer Division June 9, 2000; revision received January 20, 2001. Associate Editor: D. Poulikakos.
J. Heat Transfer. Aug 2001, 123(4): 760-769 (10 pages)
Published Online: January 20, 2001
Article history
Received:
June 9, 2000
Revised:
January 20, 2001
Citation
Vargas , J. V. C., Bejan, A., and Siems, D. L. (January 20, 2001). "Integrative Thermodynamic Optimization of the Crossflow Heat Exchanger for an Aircraft Environmental Control System ." ASME. J. Heat Transfer. August 2001; 123(4): 760–769. https://doi.org/10.1115/1.1375811
Download citation file:
Get Email Alerts
Cited By
Estimation of thermal emission from mixture of CO2 and H2O gases and fly-ash particles
J. Heat Mass Transfer
Non-Classical Heat Transfer and Recent Progress
J. Heat Mass Transfer
Related Articles
Cost and Entropy Generation Minimization of a Cross-Flow Plate Fin Heat Exchanger Using Multi-Objective Genetic Algorithm
J. Heat Transfer (February,2011)
Second Law Analysis of Heat Exchangers
J. Heat Transfer (November,2010)
Duality of Heat Exchanger Performance in Balanced Counter-Flow Systems
J. Heat Transfer (June,2003)
Related Proceedings Papers
Related Chapters
Comparing Probabilistic Graphical Model Based and Gaussian Process Based Selections for Predicting the Temporal Observations
Intelligent Engineering Systems through Artificial Neural Networks, Volume 20
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Incremental Model Adjustment
Nonlinear Regression Modeling for Engineering Applications: Modeling, Model Validation, and Enabling Design of Experiments