A new machining process model that explicitly includes the effects of the edge hone is presented. A force balance is conducted on the lower boundary of the deformation zone leading to a machining force model. The machining force components are an explicit function of the edge radius and shear angle. An increase in edge radius leads to not only increased ploughing forces but also an increase in the chip formation forces due to an average rake angle effect. Previous attempts at assessing the ploughing components as the force intercept at zero uncut chip thickness, which attribute to the ploughing mechanism all the changes in forces that occur with changes in edge radius, are seen to be erroneous in view of this model. Calculation of shear stress on the lower boundary of the deformation zone using the new machining force model indicates that the apparent size effect when cutting with edge radiused tools is due to deformation below the tool (ploughing) and a larger chip formation component due to a lower shear angle. Increases in specific energy and shear stress are also due to shear strain and strain rate increases. A consistent material behavior model that does not vary with process input conditions like uncut chip thickness, rake angle and edge radius can be developed based on the new model. [S1087-1357(00)01302-2]
Skip Nav Destination
Article navigation
August 2000
Technical Papers
A New Model and Analysis of Orthogonal Machining With an Edge-Radiused Tool
Jairam Manjunathaiah,
Jairam Manjunathaiah
Department of Mechanical Engineering and Applied Mechanics, University of Michigan, Ann Arbor, MI 48109-2125
Search for other works by this author on:
William J. Endres
William J. Endres
Department of Mechanical Engineering and Applied Mechanics, University of Michigan, Ann Arbor, MI 48109-2125
Search for other works by this author on:
Jairam Manjunathaiah
Department of Mechanical Engineering and Applied Mechanics, University of Michigan, Ann Arbor, MI 48109-2125
William J. Endres
Department of Mechanical Engineering and Applied Mechanics, University of Michigan, Ann Arbor, MI 48109-2125
Contributed by the Manufacturing Engineering Division for publication in the JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING. Manuscript received Dec. 1997; revised Sept. 1999. Associate Technical Editor: K. Ehmann.
J. Manuf. Sci. Eng. Aug 2000, 122(3): 384-390 (7 pages)
Published Online: September 1, 1999
Article history
Received:
December 1, 1997
Revised:
September 1, 1999
Citation
Manjunathaiah , J., and Endres, W. J. (September 1, 1999). "A New Model and Analysis of Orthogonal Machining With an Edge-Radiused Tool ." ASME. J. Manuf. Sci. Eng. August 2000; 122(3): 384–390. https://doi.org/10.1115/1.1285886
Download citation file:
Get Email Alerts
Related Articles
Mechanics of Machining With Chamfered Tools
J. Manuf. Sci. Eng (November,2000)
Application of an Internally Consistent Material Model to Determine the Effect of Tool Edge Geometry in Orthogonal Machining
J. Manuf. Sci. Eng (August,2002)
A Study of Burr Formation Processes Using the Finite Element Method: Part II—The Influences of Exit Angle, Rake Angle, and Backup Material on Burr Formation Processes
J. Eng. Mater. Technol (April,2000)
Chaotic Phenomena Induced by the Fast Plastic Deformation of Metals During Cutting
J. Appl. Mech (March,2006)
Related Proceedings Papers
Related Chapters
Cutting and Machining
Fabrication of Metallic Pressure Vessels
Modeling of Cutting Force in Vibration-Assisted Machining
Vibration Assisted Machining: Theory, Modelling and Applications
Development of Portable Facing Machine Tool for Machining of Tube Sheet and Shell of a Heat Exchanger
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)