Made from biomaterials, tissue scaffolds are three-dimensional (3D) constructs with highly interconnected pore networks for facilitating cell growth and flow transport of nutrients and metabolic waste. To fabricate the scaffolds with complex structures, dispensing-based rapid prototyping technique has been employed recently. In such a fabrication process, the flow rate of biomaterial dispensed is of importance since it directly contributes to the pore size and porosity of the scaffold fabricated. However, the modeling of the flow rate has proven to be a challenging task due to its complexity. This paper presents the development of a model for the flow rate in the scaffold fabrication process based on the fundamentals of fluid mechanics. To verify the effectiveness of the developed model, experiments were carried out, in which the chitosan solution (2% w/v) in acetic acid was used for dispensing under different applied pressures (, , , , and ) and needle heater temperatures (, , , and ). The measured flow rates were used to identify the flow behavior of the solution and were compared to the predictions from the developed model to illustrate the model effectiveness. Based on the developed model, simulations were carried out to identify the effects of the needle size and the flow behavior on the flow rate in the scaffold fabrication process. The developed model was also applied to determine the dispensing conditions for fabricating 3D scaffolds from a 50% chitosan-hydroxyapatite colloidal gel. As an example, a scaffold fabricated with a well-controlled internal structure of diameters of and pore sizes of in the horizontal plane and of in the vertical direction is presented in this paper to illustrate the promise of the developed model as applied to the 3D scaffold fabrication.
Skip Nav Destination
e-mail: xbc719@mail.usask.ca
Article navigation
April 2008
Research Papers
Modeling of the Flow Rate in the Dispensing-Based Process for Fabricating Tissue Scaffolds
X. B. Chen,
X. B. Chen
Department of Mechanical Engineering,
e-mail: xbc719@mail.usask.ca
University of Saskatchewan
, Saskatoon, SK, S7N 5A9, Canada
Search for other works by this author on:
M. G. Li,
M. G. Li
Department of Mechanical Engineering,
University of Saskatchewan
, Saskatoon, SK, S7N 5A9, Canada
Search for other works by this author on:
H. Ke
H. Ke
Department of Mechanical Engineering,
University of Saskatchewan
, Saskatoon, SK, S7N 5A9, Canada
Search for other works by this author on:
X. B. Chen
Department of Mechanical Engineering,
University of Saskatchewan
, Saskatoon, SK, S7N 5A9, Canadae-mail: xbc719@mail.usask.ca
M. G. Li
Department of Mechanical Engineering,
University of Saskatchewan
, Saskatoon, SK, S7N 5A9, Canada
H. Ke
Department of Mechanical Engineering,
University of Saskatchewan
, Saskatoon, SK, S7N 5A9, CanadaJ. Manuf. Sci. Eng. Apr 2008, 130(2): 021003 (7 pages)
Published Online: March 7, 2008
Article history
Received:
December 29, 2006
Revised:
August 20, 2007
Published:
March 7, 2008
Citation
Chen, X. B., Li, M. G., and Ke, H. (March 7, 2008). "Modeling of the Flow Rate in the Dispensing-Based Process for Fabricating Tissue Scaffolds." ASME. J. Manuf. Sci. Eng. April 2008; 130(2): 021003. https://doi.org/10.1115/1.2789725
Download citation file:
Get Email Alerts
Special Issue on the State-of-the-Art in Japanese Manufacturing Research
J. Manuf. Sci. Eng
A Review of Advanced Roll-to-Roll Manufacturing: System Modeling and Control
J. Manuf. Sci. Eng (April 2025)
Related Articles
Modeling of Spatially Controlled Biomolecules in Three-Dimensional Porous Alginate Structures
J. Med. Devices (December,2010)
A Wireless Insufflation System for Capsular Endoscopes
J. Med. Devices (June,2009)
Lithography Technique for Topographical Micropatterning of Collagen-Glycosaminoglycan Membranes for Tissue Engineering Applications
J. Med. Devices (September,2007)
Related Proceedings Papers
Related Chapters
Synthesis and Characterization of Carboxymethyl Chitosan Based Hybrid Biopolymer Scaffold
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
Characterization of Macro-, Micro- and Nano-Biomaterials
Biopolymers Based Micro- and Nano-Materials
Applications of Macro-, Micro- and Nano-Biomaterials Prepared using Biopolymers
Biopolymers Based Micro- and Nano-Materials