... qualification and quantification of TRGOs in PVA were evaluated through tension and nanoindentation tests, as well as elastic modulus mapping by nanoindentation. The results demonstrated a good dispersion of TRGOs in the PVA matrix, resulting in exceptional mechanical properties. The dispersion time and energy...

.... The deposition strategies with substrate preheating significantly decreased the residual stress with moderately improved mechanical properties. The combination of substrate preheating, interlayer dwell, and postheat treatment has shown an outstanding reduction of residual stress along with a remarkable...

.... , and Allafchian , A. , 2016 , “ Effect of Bonding Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4 V to AISI 304 Transient Liquid Phase Bonded Joint ,” Mater. Des. , 99 , pp. 543 – 551 . 10.1016/j.matdes.2016.03.101 [8] Kundu , S. , Sam , S. , and Chatterjee , S...

..., the present study compares the mechanical properties of AM 17-4 PH stainless steel samples with those of wrought 17-4 PH samples. Stress intensity factor and J integral were used to measure fracture toughness of the specimens. The change in fracture toughness with strain rate was evaluated by simulating two...

... with their quasi-static and dynamic mechanical properties. These characterizations include assessment of the CNTY homogeneity by means of Raman spectroscopy mapping, determination of linear density and porosity, atomic force microscopy, and dedicated measurements of the statistical distribution of the yarn’s...

... during post-processing had a significant influence on the microstructure and subsequently the mechanical properties of the lattices. Oxygen content analysis was conducted to confirm the oxygen diffusion through the strurts’ peripheries. The effect of oxygen diffusion during the HIPing and sub-transus HT...

...Yusuke Matsuda; Aref Samadi-Dooki; Yinjie Cen; Gisela Vasquez; Luke Bu Polymer coatings are widely used in industrial applications. The mechanical properties of these polymer coatings are known to vary with temperature and deformation rate. The characterization of the dynamic mechanical properties...

.... Statistically significant differences were observed in the mechanical properties based on tension testing and Izod impact testing, while differences in thermal properties based on differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were less significant. Test samples with 30 wt% lignin...

... of the mechanical properties of this material by a suite of computational and experimental approaches. First, we present parameterization of an interatomic potential for modeling monolayer as well as multilayered MoTe 2 films. For generating the empirical potential parameter set, we fit results from density...

...Donghui Wang; Shaogang Wang; Wen Zhang The dissimilar titanium alloys Ti70/TA5 are welded by using electron beam welding. The microstructure and mechanical properties of the welded joints are systematically investigated, and the welding parameters are optimized. Results show that the fusion zone...

... welding methods on metallurgical and mechanical properties, the welded joints were examined using optical microscopy, scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS) and also subjected to radiographic, hardness, tensile, and notched impact tests. The weld metal (WM) region...

...Shih-Ying Chang; An-Bang Wu; Jun-Yen Lee; Yan-Hua Huang The microstructure, thermal behavior, and mechanical properties of Sn-xZn-0.1RE (x = 5, 10, 20, and 30 wt%) alloys containing mixed trace rare earth elements were investigated in this study. The results showed that the alloys had the same...

... ), pp. 1723 – 1724 . 10.1177/002199803035189 [10] John , J. L. , Isabelle , A. , and Benjamin , M. A. , 1949 , “ Mechanical Properties of Laminated Plastics at −70°, 77°, and 200°F ,” J. Res. Natl. Bur. Stand. 43 , pp. 257 – 289 . [11] Sohn , M. S. , Hu , X. Z...

.... , Escalera , M. D. , and Sanchez , M. , 2005 , “ Characterization of Interfacial Mechanical Properties in Carbon Fiber/Aluminum Matrix Composites by the Nanoindentation Technique ,” Compos. Sci. Technol. , 65 , pp. 2025 – 2038 . 10.1016/j.compscitech.2005.04.013 [2] Xu , L. R. , Li...

... behavior at all test temperatures. The directionality of flow stress and initial strain-hardening rates in stage III were discussed based on the Schmid factors of material. Mg alloy plastic anisotropy strain hardening mechanical properties Since magnesium is the lightest of all structural...

... by ignition, and dynamic high overload. In addition, the storage and working states are often at different environmental temperatures. These span not only the static state under constant temperature but also varying temperatures or high strain rates. Because the mechanical properties of polymers are sensitive...

... requires a meticulous understanding of the process and consequent mechanical properties of the welds in order to be used in the production of high performance components. The present work deals with an experimental campaign aimed at the evaluation of the mechanical properties of AA6060 T6 friction stir...

...M. K. Hossain; K. A. Imran; M. V. Hosur; S. Jeelani Composites used for marine applications are subjected to various environmental effects, such as moisture, temperature, UV radiation, and seawater. In this study, effect of seawater on the degradation of mechanical properties of conventional...

...G. C. Saha; T. I. Khan High velocity oxy-fuel spraying was used to develop a near-nanocrystalline coating from a duplex Co coated WC-17Co powder feedstock. A microstructural and mechanical property characterization of the coating with a similar microcrystalline coating of the same composition...

... indentation mechanical properties strain hardening vickers hardness The vickers hardness alone does not include information regarding the pile-up or sink-in of the material close to the contact perimeter. Note that contrary to HV, the average contact area at maximum load p av contains...