Elastic-plastic crack front fields in arc-shaped tension specimens (C-specimens) were analyzed by a three-dimensional finite element method. The effect of side grooves on the ductile fracture behavior was investigated by studying the J-integral distribution, plane-strain constraint parameter, and development of plastic zones and comparing to experimental data. The applicability of the η factor (derived for use with compact tension specimens) for the calculation of J-integral values for the C-specimen was also investigated. The results show that side grooves promote and establish near plane strain conditions at the crack front in sub-size specimens. It was also found that a two-dimensional plane-strain analysis in conjunction with the standard American Society for Testing and Materials (ASTM) tests was sufficient to determine the fracture toughness values from side-grooved C-specimen. The results indicate the η factor for compact tension specimen as specified in the ASTM standards appears to produce reliable results for the calculation of J of C-specimens.

Issue Section:
Technical Papers
Keywords:
pressure vessels, fracture toughness testing, fracture toughness, ductile fracture, finite element analysis, crack-edge stress field analysis, stress-strain relations, elastoplasticity, Arc-Shaped Tension Specimen, Elastic-Plastic Fracture, Three Dimensional, Crack-Front Field, Finite Element Method, Side-Groove, η Factor
Topics:
Finite element analysis, Fracture (Materials), Fracture toughness, Plane strain, Stress, Tension, Testing, ASTM International
1.
ASTM E 399-97, “Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials,” ASTM.
2.
Brosa
,
V. G.
,
Bernal
,
C.
, and
Frontini
,
P.
,
1999
, “
Calibration of Fracture Mechanics Parameters and J-R Curve Determination in Polyethylene Side-Grooved Arc-Shaped Specimens
,”
Eng. Fract. Mech.
,
62
, pp.
231
–
248
.
3.
Goan
,
J. M.
,
Sutton
,
M. A.
, and
Chao
,
Y. J.
,
1990
, “
Assessment of the Engineering Approach for the Evaluation of C-Shaped Specimens
,”
ASME J. Pressure Vessel Technol.
,
112
, pp.
353
–
365
.
4.
Paris, P. C., 1977, “Fracture Mechanic in the Elastic-Plastic Regime,” Flaw Growth and Fracture, ASTM STP 631, American Society for Testing and Materials, pp. 3–27.
5.
Paris, P. C., Tada, H., Zahoor, A., and Ernst, H., 1979, “The Theory of Instability of the Tearing Mode of Elastic-Plastic Crack Growth,” Elastic-Plastic Fracture, ASTM STP 668, American Society for Testing and Materials, pp. 5–36.
6.
Landes, J. D., and Begley, J. A., 1972, “The Effect of Specimen Geometry on JIC,” Fracture Toughness, ASTM STP 514, American Society for Testing and Materials, pp. 24–39.
7.
Landes, J. D., and Begley, J. A., 1974, “Test Results From J-Integral Studies: An Attempt to Establish a JIC Testing Procedure,” Fracture Analysis, ASTM STP 560, American Society for Testing and Materials, pp. 170–186.
8.
deLorenzi
,
H. G.
, and
Shih
,
C. F.
,
1977
, “
Elastic Compliances and Stress-Intensity Factors for Side-Grooved Compact Specimens
,”
Int. J. Fract.
,
13
, pp.
544
–
548
.
9.
deLorenzi
,
H. G.
, and
Shih
,
C. F.
,
1983
, “
Three-Dimensional Elastic-Plastic Investigation of Fracture Toughness Parameters in Side-Grooved Compact Specimen
,”
Int. J. Fract.
,
21
, pp.
195
–
220
.
10.
Poulose
,
P. K.
,
1987
, “
Determination of Fracture Toughness From Thin Side-Grooved Specimens
,”
Eng. Fract. Mech.
,
26
(
2
), pp.
203
–
211
.
11.
Zhang
,
X. P.
, and
Shi
,
Y. W.
,
1992
, “
Constraint of Side-Groove and Its Influence on Fracture Toughness Parameter in Charpy-Size Specimens
,”
Eng. Fract. Mech.
,
43
(
5
), pp.
863
–
867
.
12.
Rice
,
J. R.
,
1968
, “
A Path Independent Integral and the Approximate Analysis of Strain Concentration by Notches and Cracks
,”
ASME J. Appl. Mech.
,
35
, pp.
379
–
386
.
13.
ABAQUS, 2001, Version 6.2-1, Hibbitt, Karlsson and Sorensen, Inc., Pawtucket, RI.
14.
Han
,
L.
,
Deng
,
Y.
, and
Liu
,
C.
,
1999
, “
The Determination of JIC for Polyethylene Pipe Using Non-Standard Arc-Shaped Specimen
,”
Int. J. Pressure Vessels Piping
,
76
, pp.
647
–
651
.
15.
Elfer
,
N.
, and
Bachmann
,
V.
,
1984
, “
Errors in the Determination of JIC Using Arc-Shaped Specimens
,”
Int. J. Fract.
,
24
, pp.
73
–
80
.
16.
Imai
,
Y.
, and
Matake
,
T.
,
1982
, “
Effects of Side Grooves on the Elastic-Plastic Stress State of Fracture Toughness Specimens—Three Dimensional Finite Element Analysis
,”
Eng. Fract. Mech.
,
16
(
5
), pp.
659
–
668
.
17.
ASTM E 1820-99a, “Standard Test Method for Measurement of Fracture Toughness,” ASTM.
Copyright © 2004
 by ASME
You do not currently have access to this content.