Skip Nav Destination
Issues
May 2007
ISSN 0094-9930
EISSN 1528-8978
In this Issue
Editorial
Special Issue of the JPVT From the Design and Analysis Committee
J. Pressure Vessel Technol. May 2007, 129(2): 225.
doi: https://doi.org/10.1115/1.2722298
Topics:
Design
,
Pipes
,
Pressure vessels
Research Papers
Dynamic Pipe Stresses During Water Hammer: A Finite Element Approach
J. Pressure Vessel Technol. May 2007, 129(2): 226–233.
doi: https://doi.org/10.1115/1.2716420
Topics:
Finite element analysis
,
Pipes
,
Stress
,
Pressure
,
Water hammer
,
Waves
Comparison of Residual Stresses in the Mechanical Roll Expansion of HX Tubes Into TEMA Grooves
J. Pressure Vessel Technol. May 2007, 129(2): 234–241.
doi: https://doi.org/10.1115/1.2716426
Topics:
Finite element analysis
,
Heat exchangers
,
Residual stresses
,
Stainless steel
,
Stress
Improving the Reliability of the Tube-Hydroforming Process by the Taguchi Method
J. Pressure Vessel Technol. May 2007, 129(2): 242–247.
doi: https://doi.org/10.1115/1.2716427
Topics:
Design
,
Finite element analysis
,
Reliability
,
Simulation
,
Taguchi methods
Slip Blinds at Pressures Causing Permanent Deformation
J. Pressure Vessel Technol. May 2007, 129(2): 248–253.
doi: https://doi.org/10.1115/1.2716428
Topics:
Deformation
,
Finite element analysis
,
Flanges
,
Pipes
,
Pressure
,
Deflection
,
Testing
Modeling of the Behavior of a Welded Joint Subjected to Reverse Bending Moment at High Temperature
J. Pressure Vessel Technol. May 2007, 129(2): 254–261.
doi: https://doi.org/10.1115/1.2716429
Topics:
Creep
,
Failure
,
Fatigue
,
Stress
,
Welded joints
,
Modeling
,
Plasticity
,
Damage
,
High temperature
,
Cycles
Steady-State Thermal Simulation of Weld Applied to a Practical Axisymmetric Weldment
J. Pressure Vessel Technol. May 2007, 129(2): 262–271.
doi: https://doi.org/10.1115/1.2716430
Topics:
Computational fluid dynamics
,
Heat
,
Simulation
,
Steady state
,
Temperature
,
Welded joints
,
Thermal analysis
Failure of Locally Buckled Pipelines
J. Pressure Vessel Technol. May 2007, 129(2): 272–279.
doi: https://doi.org/10.1115/1.2716431
Topics:
Cycles
,
Failure
,
Finite element analysis
,
Pipelines
,
Pipes
,
Pressure
,
Simulation
,
Steel
,
Stress
,
Fatigue
Limit Loads of Pressure Components Using the Reference Two-Bar Structure
J. Pressure Vessel Technol. May 2007, 129(2): 280–286.
doi: https://doi.org/10.1115/1.2716432
Shakedown Limits of a Pipe Bend Using Small and Large Displacement Formulations
J. Pressure Vessel Technol. May 2007, 129(2): 287–295.
doi: https://doi.org/10.1115/1.2716433
Topics:
Displacement
,
Pipe bends
,
Stress
,
Pressure
Local Limit-Load Analysis Using the Method
J. Pressure Vessel Technol. May 2007, 129(2): 296–305.
doi: https://doi.org/10.1115/1.2716434
Topics:
Elastic moduli
,
Stress
,
Finite element analysis
,
Fracture (Materials)
Mode-I Stress-Intensity Factors for a Cracked Slab Under an Arbitrary Thermal Shock
J. Pressure Vessel Technol. May 2007, 129(2): 306–312.
doi: https://doi.org/10.1115/1.2716435
Topics:
Polynomials
,
Slabs
,
Stress
,
Thermal shock
,
Transients (Dynamics)
,
Fracture (Materials)
,
Thermoelasticity
High-Temperature Heat Exchanger Tube-Sheet Assembly Investigation With Computational Fluid Dynamics
J. Pressure Vessel Technol. May 2007, 129(2): 313–315.
doi: https://doi.org/10.1115/1.2716436
Considerations in the Design and Analysis of an ASME Section VIII, Div. 2 Reactor Support Skirt
J. Pressure Vessel Technol. May 2007, 129(2): 316–322.
doi: https://doi.org/10.1115/1.2722301
Topics:
Boundary-value problems
,
Design
,
Finite element analysis
,
Fourier series
,
Stress
,
Temperature
,
Friction
,
Shells
,
Vessels
,
Heat transfer
Technical Brief
Note on Shear Load-Testing Feedwater Heater Tube Joints
J. Pressure Vessel Technol. May 2007, 129(2): 323–325.
doi: https://doi.org/10.1115/1.2716437
Topics:
Feedwater
,
Shear (Mechanics)
,
Stress
,
Testing
,
Welded joints
,
Welding
,
Deformation
,
Tensile strength
,
Tubular joints
,
Metals
Design Innovation Papers
Proposed Design Criterion for Vessel Lifting Lugs in Lieu of ASME B30.20
J. Pressure Vessel Technol. May 2007, 129(2): 326–333.
doi: https://doi.org/10.1115/1.2716439
Topics:
Design
,
Stress
,
Vessels
,
Regulations
,
Pressure vessels
,
Failure
,
Safety
,
Safety engineering
Design for Leakage in Flange Joints Under External Loads
J. Pressure Vessel Technol. May 2007, 129(2): 334–337.
doi: https://doi.org/10.1115/1.2716700
Determining Effective Thickness of Cylinders in Pressure Equipment With Significant Thickness Variations for Fitness for Service Assessments
J. Pressure Vessel Technol. May 2007, 129(2): 338–341.
doi: https://doi.org/10.1115/1.2716440
Topics:
Corrosion
,
Cylinders
,
Fitness-for-service
,
Maintenance
,
Pressure equipment
,
Erosion
,
Vessels
Erratum
Erratum: “Incorporating Neural Network Material Models Within Finite Element Analysis for Rheological Behavior Prediction” [Journal of Pressure Vessel Technology, 2007, 129(1), pp. 58–65]
J. Pressure Vessel Technol. May 2007, 129(2): 342.
doi: https://doi.org/10.1115/1.2728894
Email alerts
RSS Feeds
Analysis of Factors Influencing Y-Ring Sealing Under Ultra-High-Pressure, High-Temperature, and Low-Temperature Conditions
J. Pressure Vessel Technol (February 2025)