In this paper, the relationships between the power augmentation of a HAWT due to Mie-type tip vane application and other factors influencing the efficiency of a wind turbine such as the blade aspect ratio, number of blades, blade pitch angle and Reynolds number are investigated. Experiments were carried out in a wind tunnel with an open, 3.6 m diameter, test section. Rotor models included two- and three-blade upwind turbines with four sets of blades with different aspect ratios. With the rotor blades tested, a maximum power augmentation of about 14.5% was achieved due to Mie vane application. The relationships between power augmentation due to the Mie vane and the above factors are investigated. It is found that the application of a tip-mounted Mie vane results in a larger increase in maximum power coefficient for rotors with smaller aspect ratios and for lower wind speeds. Surface oil film and surface tuft visualization methods were used to detect the flow patterns at the blade tip. Addition of the Mie vanes causes significant changes in flow behavior near the blade tip, resulting in additional blade lift.

Issue Section:
Technical Papers
Keywords:
wind turbines, rotors, wind tunnels, external flows
Topics:
Blades, Reynolds number, Rotors, Wind turbines, Wind tunnels, Horizontal axis wind turbines, Flow (Dynamics), Wind velocity
1.
Shimizu, Y., Van Bussel, G. J., Matsumura, S., Bruining, A., Kikuyama, K., and Hasegawa, Y., 1990, “Studies on Horizontal Axis Wind Turbines With Tip Attachments,” Proc. ECWEC ’90, Madrid, Spain, pp. 279–283.
2.
Shimizu, Y., Van Bussel, G. J., Matsumura, S., and Bruining, A., 1991, “New Technology of Power Augmentation on Horizontal Axis Wind Turbines Using Mie Vanes,” Proc. of EWEC ’91, Amsterdam, The Netherlands, pp. 221–225.
3.
Shimizu
,
Y.
,
Yoshikawa
,
T.
, and
Matsumura
,
S.
,
1994
, “
Power Augmentation Effects of a Horizontal Axis Wind Turbine With a Tip Vane-Part 1: Turbine Performance and Tip Vane Configuration
,”
ASME J. Fluids Eng.
,
116
, pp.
287
–
292
.
4.
Shimizu
,
Y.
,
Yoshikawa
,
T.
, and
Matsumura
,
S.
,
1994
, “
Power Augmentation Effects of a Horizontal Axis Wind Turbine With a Tip Vane-Part 2: Flow Visualization
,”
ASME J. Fluids Eng.
,
116
, pp.
293
–
297
.
5.
Shimizu, Y., Maeda, T., Kamada, Y., and Seto, H., 2000, “Effects of Mie Tip Vane on Pressure Distribution of Rotor Blade and Power Augmentation of Horizontal Axis Wind Turbine,” Proc. ISROMAC-8, Hawaii, 1, pp. 42–48.
6.
Shimizu
,
Y.
,
Imamura
,
H.
,
Matsumura
,
S.
, and
Maeda
,
T.
,
1995
, “
Power Augmentation of a Horizontal Axis Wind Turbine Using a Mie-Type Tip Vane: Velocity Distribution Around the Tip of a HAWT Blade With and Without a Mie-Type Tip Vane
,”
ASME J. Sol. Energy Eng.
,
117
, pp.
297
–
303
.
7.
Zeqiang, L., and Dahlberg, J., 1988, “Measurement on SVIAB Wind Turbines in CARDC Large Wind Tunnel. Performance Test and Comparison With Calculation,” Proc. APWEC ’88, Shanghai, China, pp. 401–408.
8.
Vermeer, L. J., 2001, “A Review of Wind Turbine Wake Research at TUDelft,” Proc. 2001 ASME Wind Energy Symposium, AIAA, paper no. 2001–0030.
9.
Shimizu, Y., 1999, Wind Power Technology, pp. 190, Power-sha, Tokyo.
10.
Bertin, J., and Smith, M. L., 1979, Aerodynamics for Engineers, pp. 172, Prentice-Hall, Inc., New Jersey.
11.
Kroo
,
I.
,
2001
, “
Drag Due to Lift: Concepts for Prediction and Reduction
,”
Ann. Rev. Fluid Mech.
,
33
, pp.
587
–
617
.
12.
Burton, T., Sharpe, D., Jenkins, N., and Bossanyi, E., 2001, Wind Energy Handbook, pp. 174, John Wiley & Sons, Ltd, West Sussex, UK.
Copyright © 2003
 by ASME
You do not currently have access to this content.