Frictional behavior and topographical changes of material surfaces with applications in the microelectronics industry were experimentally observed. This work was performed to unveil trends in tribological characteristics of porous polyurethane material separately against copper and silicon dioxide materials typically found in integrated circuit (IC) polishing manufacturing processes. A linear reciprocating tribometer was utilized to translate the loaded contact of the polymer and contacting materials in the presence of a colloidal silica slurry. Contact forces were monitored throughout the experiments while surface topography of contacting surfaces was quantified using profilometry. Trials of polishing experiments were performed through a range of normal pressures and velocities to identify trends of interest, which are important in polishing. Coefficients of friction (COFs) between the polymer and contacting materials showed a decreasing trend with increasing polishing time and distance traveled. The copper and polymer material contacts were found to have a lower COF than that for the silicon dioxide and polymer contacts. Surface roughness of the polymer showed a general decreasing trend with increasing polishing time. This trend indicates a potential correlation between polymer surface roughness and the COF between the polymer and contacting materials. Evolution of the surface roughness of the materials differed depending on the direction along which topography was measured. An uncertainty analysis of the quantified parameters was conducted to provide knowledge in the confidence of the experimental results. Tribological behavior of the porous polyurethane and copper and silicon dioxide contacts is gathered from this experimental work for more complete characterization of the material.
Skip Nav Destination
Article navigation
July 2016
Research-Article
Frictional Behavior and Topography of Porous Polyurethane on Copper and Silicon Dioxide Articulating Contacts
David C. Ponte,
David C. Ponte
Mechanical Engineering,
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dcp1191@my.uri.edu
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dcp1191@my.uri.edu
Search for other works by this author on:
D. M. L. Meyer
D. M. L. Meyer
Mechanical Engineering,
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dmmeyer@uri.edu
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dmmeyer@uri.edu
Search for other works by this author on:
David C. Ponte
Mechanical Engineering,
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dcp1191@my.uri.edu
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dcp1191@my.uri.edu
D. M. L. Meyer
Mechanical Engineering,
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dmmeyer@uri.edu
University of Rhode Island,
92 Upper College Road,
Kingston, RI 02881
e-mail: dmmeyer@uri.edu
1Corresponding author.
Contributed by the Tribology Division of ASME for publication in the JOURNAL OF TRIBOLOGY. Manuscript received August 19, 2015; final manuscript received December 26, 2015; published online April 25, 2016. Assoc. Editor: Sinan Muftu.
J. Tribol. Jul 2016, 138(3): 031604 (9 pages)
Published Online: April 25, 2016
Article history
Received:
August 19, 2015
Revised:
December 26, 2015
Citation
Ponte, D. C., and Meyer, D. M. L. (April 25, 2016). "Frictional Behavior and Topography of Porous Polyurethane on Copper and Silicon Dioxide Articulating Contacts." ASME. J. Tribol. July 2016; 138(3): 031604. https://doi.org/10.1115/1.4032523
Download citation file:
Get Email Alerts
Cited By
Related Articles
Fabrication of Cu Surface Composite Reinforced by Ni Particles Via Friction Stir Processing: Microstructure and Tribology Behaviors
J. Tribol (January,2018)
Optimizing the Tribological Behavior of Hybrid Copper Surface Composites Using Statistical and Machine Learning Techniques
J. Tribol (May,2018)
Insights on the tribological characteristics of titanium alloys in demanding environments
J. Tribol (January,0001)
Development and Optimization of a Tribometer for Radial Shaft Seals
J. Tribol (April,2021)
Related Chapters
The Tribological Character of LB Films of Dipalmitoylphosphatidylcholine (DPPC)
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
Contact Laws
Contact in Structural Mechanics: A Weighted Residual Approach
Friction and Wear of Polymers and Composites
Tribology of Mechanical Systems: A Guide to Present and Future Technologies