Local flow behavior and heat transfer results are presented from two swirl chambers, which model passages used to cool the leading edges of turbine blades in gas turbine engines. Flow results are obtained in an isothermal swirl chamber. Surface Nusselt number distributions are measured in a second swirl chamber (with a constant wall heat flux boundary condition) using infrared thermography in conjunction with thermocouples, energy balances, and in situ calibration procedures. In both cases, Reynolds numbers Re based on inlet duct characteristics range from 6000 to about 20,000. Bulk helical flow is produced in each chamber by two inlets, which are tangent to the swirl chamber circumference. Important changes to local and globally averaged surface Nusselt numbers, instantaneous flow structure from flow visualizations, and distributions of static pressure, total pressure, and circumferential velocity are observed throughout the swirl chambers as the Reynolds number increases. Of particular importance are increases of local surface Nusselt numbers (as well as ones globally averaged over the entire swirl chamber surface) with increasing Reynolds number. These are tied to increased advection, as well as important changes to vortex characteristics near the concave surfaces of the swirl chambers. Higher Re also give larger axial components of velocity, and increased turning of the flow from each inlet, which gives Go¨rtler vortex pair trajectories greater skewness as they are advected downstream of each inlet. [S0889-504X(00)00502-X]
Skip Nav Destination
Article navigation
April 2000
Technical Papers
Local Swirl Chamber Heat Transfer and Flow Structure at Different Reynolds Numbers
C. R. Hedlund, Mem. ASME,
C. R. Hedlund, Mem. ASME
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, University of Utah, Salt Lake City, UT 84112
11
Search for other works by this author on:
P. M. Ligrani, Mem. ASME, Professor
P. M. Ligrani, Mem. ASME, Professor
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, University of Utah, Salt Lake City, UT 84112
Search for other works by this author on:
C. R. Hedlund, Mem. ASME
11
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, University of Utah, Salt Lake City, UT 84112
P. M. Ligrani, Mem. ASME, Professor
Convective Heat Transfer Laboratory, Department of Mechanical Engineering, University of Utah, Salt Lake City, UT 84112
Contributed by the International Gas Turbine Institute and presented at the 44th International Gas Turbine and Aeroengine Congress and Exhibition, Indianapolis, Indiana, June 7–10, 1999. Manuscript received by the International Gas Turbine Institute February 1999. Paper No. 99-GT-164. Review Chair: D. C. Wisler.
J. Turbomach. Apr 2000, 122(2): 375-385 (11 pages)
Published Online: February 1, 1999
Article history
Received:
February 1, 1999
Citation
Hedlund, C. R., and Ligrani, P. M. (February 1, 1999). "Local Swirl Chamber Heat Transfer and Flow Structure at Different Reynolds Numbers ." ASME. J. Turbomach. April 2000; 122(2): 375–385. https://doi.org/10.1115/1.555458
Download citation file:
Get Email Alerts
Evaluating Thin-Film Thermocouple Performance on Additively Manufactured Turbine Airfoils
J. Turbomach (July 2025)
Thermohydraulic Performance and Flow Structures of Diamond Pyramid Arrays
J. Turbomach (July 2025)
Related Articles
Heat Transfer and Flow Phenomena in a Swirl Chamber Simulating Turbine Blade Internal Cooling
J. Turbomach (October,1999)
Effects of Rib Arrangements on Heat Transfer and Flow Behavior in a Rectangular Rib-Roughened Passage: Application to Cooling of Gas Turbine Blade Trailing Edge
J. Heat Transfer (August,2001)
Heat Transfer for a Turbine Blade With Nonaxisymmetric Endwall Contouring
J. Turbomach (January,2011)
Local Heat Transfer and Flow Structure on and Above a Dimpled Surface in a Channel
J. Turbomach (January,2001)
Related Proceedings Papers
Related Chapters
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Thermodynamic Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Thermal Design Guide of Liquid Cooled Systems
Thermal Design of Liquid Cooled Microelectronic Equipment