Local heat transfer coefficients on a flat plate surface downstream a row of cylindrical ejection holes were investigated. The parameters blowing angle, hole pitch, blowing rate, and density ratio were varied over a wide range, emphasizing engine relevant conditions. A high-resolution IR-thermography technique was used for measuring surface temperature fields. Local heat transfer coefficients were obtained from a Finite Element analysis. IR-determined surface temperatures and backside temperatures of the cooled test plate measured with thermocouples were applied as boundary conditions in this heat flux computation. The superposition approach was employed to obtain the heat transfer coefficient based on the difference between actual wall temperatures and adiabatic wall temperatures in the presence of film cooling. The data are given for an engine relevant density ratio of 1.8. Therefore, heat transfer results with different wall temperature conditions and adiabatic film cooling effectiveness results for identical flow situations (i.e., constant density ratios) were combined. Characteristic surface patterns of the locally resolved heat transfer coefficients are recognized and quantified as the different ejection parameters are changed. The detailed results are used to discuss the specific local heat transfer behavior in the presence of film cooling. They also provide a base of surface data essential for the validation of the heat transfer capabilities of CFD codes in discrete hole film cooling.
Skip Nav Destination
Article navigation
October 2001
Technical Papers
High-Resolution Measurements of Local Heat Transfer Coefficients From Discrete Hole Film Cooling
S. Baldauf,
S. Baldauf
Lehrstuhl und Institut fu¨r Thermische Stro¨mungsmaschinen, Universita¨t Karlsruhe (TH), 76128 Karlsruhe, Germany
Search for other works by this author on:
A. Schulz,
A. Schulz
Lehrstuhl und Institut fu¨r Thermische Stro¨mungsmaschinen, Universita¨t Karlsruhe (TH), 76128 Karlsruhe, Germany
Search for other works by this author on:
S. Wittig
S. Wittig
Lehrstuhl und Institut fu¨r Thermische Stro¨mungsmaschinen, Universita¨t Karlsruhe (TH), 76128 Karlsruhe, Germany
Search for other works by this author on:
S. Baldauf
Lehrstuhl und Institut fu¨r Thermische Stro¨mungsmaschinen, Universita¨t Karlsruhe (TH), 76128 Karlsruhe, Germany
A. Schulz
Lehrstuhl und Institut fu¨r Thermische Stro¨mungsmaschinen, Universita¨t Karlsruhe (TH), 76128 Karlsruhe, Germany
S. Wittig
Lehrstuhl und Institut fu¨r Thermische Stro¨mungsmaschinen, Universita¨t Karlsruhe (TH), 76128 Karlsruhe, Germany
Contributed by the International Gas Turbine Institute and presented at the 44th International Gas Turbine and Aeroengine Congress and Exhibition, Indianapolis, Indiana, June 7–10, 1999. Manuscript received by the International Gas Turbine Institute February 1999. Paper No. 99-GT-43. Review Chair: D. C. Wisler.
J. Turbomach. Oct 2001, 123(4): 749-757 (9 pages)
Published Online: February 1, 1999
Article history
Received:
February 1, 1999
Citation
Baldauf, S., Schulz , A., and Wittig, S. (February 1, 1999). "High-Resolution Measurements of Local Heat Transfer Coefficients From Discrete Hole Film Cooling ." ASME. J. Turbomach. October 2001; 123(4): 749–757. https://doi.org/10.1115/1.1387245
Download citation file:
Get Email Alerts
Related Articles
High-Resolution Measurements of Local Effectiveness From Discrete Hole Film Cooling
J. Turbomach (October,2001)
Effects of a Reacting Cross-Stream on Turbine Film Cooling
J. Eng. Gas Turbines Power (May,2010)
Experimental Investigation of Conjugate Heat Transfer in a Rib-Roughened Trailing Edge Channel With Crossing Jets
J. Turbomach (July,2012)
Film Cooling From a Row of Holes Supplemented With Antivortex Holes
J. Turbomach (April,2009)
Related Proceedings Papers
Related Chapters
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Extended Surfaces
Thermal Management of Microelectronic Equipment, Second Edition
Extended Surfaces
Thermal Management of Microelectronic Equipment