The sealing of the stator-rotor gap and rotor-platform cooling are vital to the safe operation of the high-pressure turbine. Contrary to the experience in subsonic turbines, this paper demonstrates the potential to improve the efficiency in transonic turbines at certain rim seal rates. Two types of cooling techniques were investigated: purge gas ejected out of the cavity between the stator rim and the rotor disk, and cooling at the rotor-platform. The tests were carried out in a full annular stage fed by a compression tube at , , and at temperature ratios reproducing engine conditions. The stator outlet was instrumented to allow the aerothermal characterization of the purge flow. The rotor blade was heavily instrumented with fast-response pressure sensors and double-layer thin film gauges. The tests are coupled with numerical calculations performed using the ONERA’s code ELSA. The results indicate that the stator-rotor interaction is significantly affected by the stator-rim seal, both in terms of heat transfer and pressure fluctuations. The flow exchange between the rotor disk cavity and the mainstream passage is mainly governed by the vane trailing edge shock patterns. The purge flow leads to the appearance of a large coherent vortex structure on the suction side of the blade, which enhances the overall heat transfer coefficient due to the blockage effect created. The impact of the platform cooling is observed to be restricted to the platform, with negligible effects on the blade suction side. The platform cooling results in a clear attenuation of pressure pulsations at some specific locations. The experimental and computational fluid dynamics results show an increase in the turbine performance compared with the no rim seal case. A detailed loss breakdown analysis helped to identify the shock loss as the major loss source. The presented results should help designers improve the protection of the rotor platform while minimizing the amount of coolant used.
Skip Nav Destination
Article navigation
April 2010
Research Papers
Aerothermal Impact of Stator-Rim Purge Flow and Rotor-Platform Film Cooling on a Transonic Turbine Stage
M. Pau,
M. Pau
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
Search for other works by this author on:
G. Paniagua,
G. Paniagua
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
Search for other works by this author on:
D. Delhaye,
D. Delhaye
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
Search for other works by this author on:
A. de la Loma,
A. de la Loma
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
Search for other works by this author on:
P. Ginibre
P. Ginibre
Department of Turbine Aerodynamics,
Snecma-Groupe Safran
, 77550 Moissy Cramayel, France
Search for other works by this author on:
M. Pau
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
G. Paniagua
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
D. Delhaye
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
A. de la Loma
Department of Turbomachinery and Propulsion,
von Karman Institute for Fluid Dynamics
, 1640 Rhode Saint Genèse, Belgium
P. Ginibre
Department of Turbine Aerodynamics,
Snecma-Groupe Safran
, 77550 Moissy Cramayel, FranceJ. Turbomach. Apr 2010, 132(2): 021006 (12 pages)
Published Online: January 11, 2010
Article history
Received:
May 2, 2008
Revised:
February 14, 2009
Online:
January 11, 2010
Published:
January 11, 2010
Citation
Pau, M., Paniagua, G., Delhaye, D., de la Loma, A., and Ginibre, P. (January 11, 2010). "Aerothermal Impact of Stator-Rim Purge Flow and Rotor-Platform Film Cooling on a Transonic Turbine Stage." ASME. J. Turbomach. April 2010; 132(2): 021006. https://doi.org/10.1115/1.3142859
Download citation file:
Get Email Alerts
Related Articles
Film-Cooling Effectiveness on a Rotating Turbine Platform Using Pressure Sensitive Paint Technique
J. Turbomach (October,2010)
Influence of Stator-Rotor Interaction on the Aerothermal Performance of Recess Blade Tips
J. Turbomach (January,2011)
Effects of Multiblocking and Axial Gap Distance on Performance of Partial Admission Turbines: A Numerical Analysis
J. Turbomach (July,2011)
Unsteady Forces of Rotor Blades in Full and Partial Admission Turbines
J. Turbomach (October,2011)
Related Proceedings Papers
Related Chapters
Introduction
Turbine Aerodynamics: Axial-Flow and Radial-Flow Turbine Design and Analysis
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Other Components and Variations
Axial-Flow Compressors